Get a new shower, a walk-in enclosure or a bath to shower conversion through one vetted local fitter. Shower installation in Bristol starts here with a free home survey of your water system, waste and walls, and the price follows in writing.

How much the job covers depends on the route, since a straight swap touches far less of the room than taking out a bath. On a full enclosure or conversion, expect the written quote to set out each of these.
Moving the toilet or adding underfloor heating makes it a new bathroom (bathroom installation). A fully waterproofed floor is a wet room.
A shower bought before anyone has looked at the house can turn out wrong for it. Through this service, one fitter sees your home first and the quote comes after. That way the model, the tray height and the price all follow from what is actually there.
Before anything gets ordered, ask that fitter for a written answer on these five points:
What hides under a bath stays provisional until the bath is out, so it needs its own quote line.
Three different jobs get called shower installation, and quotes for different routes cannot be compared. Need a new shower because the old one has failed? That is the smallest job, while a walk-in enclosure or a conversion means building work around the shower.
Walk-in describes the entry: a wide opening, often with a fixed glass panel and no door. It says nothing about step height, so mobility needs start with disabled bathrooms.

Before a model is chosen, three local checks can change the plan. Scale affects valves and heads, historic fabric can rule out a waste route, and a long tray needs somewhere to unload. Put any of them in your first message.
Got a bath you never use, or a shower that keeps playing up? Call 0117 463 5784 or arrange a home visit from one fitter.
Ready for a free home survey? One vetted local fitter checks the room and quotes in writing.
Book a free surveyFitting a new shower in Bristol should leave a record at each stage, because finished tiles hide the work that matters most. Ask for three dates in writing: water and power off, deliveries, and the first shower. With one shower in the house, plan where everyone will wash, and ask how an overrun is handled.
Route, make and model, boiler or water system.
One vetted fitter visits free of charge and quotes in writing.
The old shower or bath comes out.
The fitter or a plumber positions the pipework; ask for a photo and the pressure test result.
Ask for photos of the tray joint and pipe entries before any tile or panel.
Once sealants have cured, ask for test results, model details and any electrical certificate.
A shower combines water, waste and electrics, and most of that ends up behind the finish. Test any installer on those three and keep each answer with the quote. A valve fault and a joint leak can end up with different people, so settle who answers for which.
Vetting comes before listing, your job goes to just one fitter, and you sign with that fitter directly.
The route sets the starting point for a shower quote, and the survey moves it from there. A replacement is mostly product and labour, a new enclosure adds the tray, screen and waste, and a conversion adds strip-out, repairs and finishes. Beyond that, these items make the biggest difference.
A free quote that skips the route or hides provisional items is only a guess. For budgets across a whole room, read the bathroom costs guide.
Often, when the waste and floor allow it, because a bath footprint usually gives enough length for a tray. The trap still needs depth and a fall, and the walls behind the bath need repair. Ask for the waste route and walls to be checked at survey, then again once the bath is out.
No, because a low-profile tray can still leave a step. Level access means the floor and shower meet with no step, which needs room for the trap inside the floor. Drainage design falls under the building regulations in Approved Document H, and joists should never be cut without a competent check.
It depends on your water system: a mixer blends hot and cold from it, so a combi shares output with every outlet. An electric shower heats its own cold mains feed on a dedicated circuit. A power shower adds a pump, so it needs a compatible tank-fed system.
Yes, for the electrical side: a competent electrician checks the circuit, protection and rating against the new model. A new circuit or consumer unit must be notified, usually through a registered scheme. A like-for-like swap on a suitable circuit is usually not notifiable, yet it should still be tested and certified.
Not always, because shower pumps are designed for tank-fed systems and a combi or mains-fed supply usually needs a different fix. Weak flow can also come from a scaled head, a part-closed valve or narrow pipes. Ask for supply readings before anyone suggests a pump.
Four details make the visit worthwhile: the route you have in mind, the current make and model, your boiler or water system, and who will use the shower. Coverage is on the Bristol areas page, and the bathroom fitter homepage explains the referral.
To get in touch about shower installation in Bristol, call 0117 463 5784 or leave your shower details.
Last reviewed: November 2026
0117 463 5784